debug — 3c59x debug level (0-6)

options — 3c59x: Bits 0-3: media type, bit 4: bus mastering, bit 9: full duplex

global_options — 3c59x: same as options, but applies to all NICs if options is unset

full_duplex — 3c59x full duplex setting(s) (1)

global_full_duplex — 3c59x: same as full_duplex, but applies to all NICs if full_duplex is unset

hw_checksums — 3c59x Hardware checksum checking by adapter(s) (0-1)

flow_ctrl — 3c59x 802.3x flow control usage (PAUSE only) (0-1)

enable_wol — 3c59x: Turn on Wake-on-LAN for adapter(s) (0-1)

global_enable_wol — 3c59x: same as enable_wol, but applies to all NICs if enable_wol is unset

rx_copybreak — 3c59x copy breakpoint for copy-only-tiny-frames

max_interrupt_work — 3c59x maximum events handled per interrupt

compaq_ioaddr — 3c59x PCI I/O base address (Compaq BIOS problem workaround)

compaq_irq — 3c59x PCI IRQ number (Compaq BIOS problem workaround)

compaq_device_id — 3c59x PCI device ID (Compaq BIOS problem workaround)

watchdog — 3c59x transmit timeout in milliseconds

global_use_mmio — 3c59x: same as use_mmio, but applies to all NICs if options is unset

use_mmio — 3c59x: use memory-mapped PCI I/O resource (0-1)

b44_debug — B44 bitmapped debugging message enable value

disable_msi — Disable Message Signaled Interrupt (MSI)

debug — Debug level (0=none,...,16=all)

eeprom_bad_csum_allow — Allow bad eeprom checksums

TxDescriptors — Number of transmit descriptors

RxDescriptors — Number of receive descriptors

Speed — Speed setting

Duplex — Duplex setting

AutoNeg — Advertised auto-negotiation setting

FlowControl — Flow Control setting

XsumRX — Disable or enable Receive Checksum offload

TxIntDelay — Transmit Interrupt Delay

TxAbsIntDelay — Transmit Absolute Interrupt Delay

RxIntDelay — Receive Interrupt Delay

RxAbsIntDelay — Receive Absolute Interrupt Delay

InterruptThrottleRate — Interrupt Throttling Rate

SmartPowerDownEnable — Enable PHY smart power down

KumeranLockLoss — Enable Kumeran lock loss workaround

myri10ge_fw_name — Firmware image name

myri10ge_ecrc_enable — Enable Extended CRC on PCI-E

myri10ge_max_intr_slots — Interrupt queue slots

myri10ge_small_bytes — Threshold of small packets

myri10ge_msi — Enable Message Signalled Interrupts

myri10ge_intr_coal_delay — Interrupt coalescing delay

myri10ge_flow_control — Pause parameter

myri10ge_deassert_wait — Wait when deasserting legacy interrupts

myri10ge_force_firmware — Force firmware to assume aligned completions

myri10ge_skb_cross_4k — Can a small skb cross a 4KB boundary?

myri10ge_initial_mtu — Initial MTU

myri10ge_napi_weight — Set NAPI weight

myri10ge_watchdog_timeout — Set watchdog timeout

myri10ge_max_irq_loops — Set stuck legacy IRQ detection threshold

mtu — DP8381x MTU (all boards)

debug — DP8381x default debug level

rx_copybreak — DP8381x copy breakpoint for copy-only-tiny-frames

options — DP8381x: Bits 0-3: media type, bit 17: full duplex

full_duplex — DP8381x full duplex setting(s) (1)

debug — pcnet32 debug level

max_interrupt_work — pcnet32 maximum events handled per interrupt

rx_copybreak — pcnet32 copy breakpoint for copy-only-tiny-frames

tx_start_pt — pcnet32 transmit start point (0-3)

pcnet32vlb — pcnet32 Vesa local bus (VLB) support (0/1)

options — pcnet32 initial option setting(s) (0-15)

full_duplex — pcnet32 full duplex setting(s) (1)

homepna — pcnet32 mode for 79C978 cards (1 for HomePNA, 0 for Ethernet, default Ethernet

media — force phy operation. Deprecated by ethtool (8).

rx_copybreak — Copy breakpoint for copy-only-tiny-frames

use_dac — Enable PCI DAC. Unsafe on 32 bit PCI slot.

debug — Debug verbosity level (0=none, ..., 16=all)

multicast_filter_limit — SiS 900/7016 maximum number of filtered multicast addresses

max_interrupt_work — SiS 900/7016 maximum events handled per interrupt

sis900_debug — SiS 900/7016 bitmapped debugging message level

max_interrupt_work — Maximum events handled per interrupt

mtu — MTU (all boards)

debug — Debug level (0-6)

rx_copybreak — Copy breakpoint for copy-only-tiny-frames

intr_latency — Maximum interrupt latency, in microseconds

small_frames — Maximum size of receive frames that bypass interrupt latency (0,64,128,256,512)

options — Deprecated: Bits 0-3: media type, bit 17: full duplex

full_duplex — Deprecated: Forced full-duplex setting (0/1)

enable_hw_cksum — Enable/disable hardware cksum support (0/1)

tg3_debug — Tigon3 bitmapped debugging message enable value

aui — ThunderLAN use AUI port(s) (0-1)

duplex — ThunderLAN duplex setting(s) (0-default, 1-half, 2-full)

speed — ThunderLAN port speen setting(s) (0,10,100)

debug — ThunderLAN debug mask

bbuf — ThunderLAN use big buffer (0-1)

max_interrupt_work — VIA Rhine maximum events handled per interrupt

debug — VIA Rhine debug level (0-7)

rx_copybreak — VIA Rhine copy breakpoint for copy-only-tiny-frames

avoid_D3 — Avoid power state D3 (work-around for broken BIOSes)