For those interested,

Centos 5.2 64 bit runs on the new intel D945GCLF2.

This is a second generation of the intel atom mini itx board. The cpu is a atom 330, dual core cpu with HT. A grand total of 4 cpu's show up.
The network card has been upgraded to GB networking ( realtek RTL8111). Standard driver that comes with centos 5.2 does not work, but the one from realtek's website does and is straith forward to install.

The board fits a 1U casing with standard fans, which are low profile now.

Output of dmesg and lspci -vv

Linux version 2.6.18-92.el5 (mockbuild@builder10.centos.org) (gcc version 4.1.2 20071124 (Red Hat 4.1.2-42)) #1 SMP Tue Jun 10 18:51:06 EDT 2008
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f533000 (usable)
BIOS-e820: 000000001f533000 - 000000001f53b000 (reserved)
BIOS-e820: 000000001f53b000 - 000000001f5cb000 (usable)
BIOS-e820: 000000001f5cb000 - 000000001f5cf000 (reserved)
BIOS-e820: 000000001f5cf000 - 000000001f660000 (usable)
BIOS-e820: 000000001f660000 - 000000001f6f0000 (ACPI NVS)
BIOS-e820: 000000001f6f0000 - 000000001f6f3000 (usable)
BIOS-e820: 000000001f6f3000 - 000000001f6ff000 (ACPI data)
BIOS-e820: 000000001f6ff000 - 000000001f700000 (usable)
BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
BIOS-e820: 00000000f0000000 - 0000000100000000 (reserved)
DMI 2.4 present.
ACPI: RSDP (v000 INTEL ) @ 0x00000000000fe020
ACPI: RSDT (v001 INTEL D945GLF2 0x00000063 0x01000013) @ 0x000000001f6fd038
ACPI: FADT (v001 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x000000001f6fc000
ACPI: MADT (v001 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x000000001f6f6000
ACPI: WDDT (v001 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x000000001f6f5000
ACPI: MCFG (v001 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x000000001f6f4000
ACPI: ASF! (v032 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x000000001f6f3000
ACPI: DSDT (v001 INTEL D945GLF2 0x00000063 MSFT 0x01000013) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000001f700000
Bootmem setup node 0 0000000000000000-000000001f700000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
On node 0 totalpages: 125480
DMA zone: 2680 pages, LIFO batch:0
DMA32 zone: 122800 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 7:12 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 7:12 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 7:12 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 7:12 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000008f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 0000000000100000
Nosave address range: 000000001f533000 - 000000001f53b000
Nosave address range: 000000001f5cb000 - 000000001f5cf000
Nosave address range: 000000001f660000 - 000000001f6f0000
Nosave address range: 000000001f6f3000 - 000000001f6ff000
Allocating PCI resources starting at 30000000 (gap: 20000000:d0000000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 125480
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Checking aperture...
Memory: 497396k/515072k available (2457k kernel code, 16552k reserved, 1246k data, 196k init)
Calibrating delay using timer specific routine.. 3194.14 BogoMIPS (lpj=1597073)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 8313077
Detected 8.313 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 3382.68 BogoMIPS (lpj=1691340)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
Calibrating delay using timer specific routine.. 3191.72 BogoMIPS (lpj=1595863)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU2: Thermal monitoring enabled (TM1)
Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 3191.80 BogoMIPS (lpj=1595902)
CPU: L1 I cache: 32K, L1 D cache: 24K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU3: Thermal monitoring enabled (TM1)
Intel(R) Atom(TM) CPU 330 @ 1.60GHz stepping 02
Brought up 4 CPUs
testing NMI watchdog ... OK.
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1596.112 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
migration_cost=10,795
checking if image is initramfs... it is
Freeing initrd memory: 3175k freed
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000
PCI: Buses that can't use MMCONFIG will use type 1 PCI conf access.
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
pnp: 00:06: ioport range 0x500-0x53f has been reserved
pnp: 00:06: ioport range 0x400-0x47f could not be reserved
pnp: 00:06: ioport range 0x680-0x6ff has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: 1000-1fff
MEM window: 28100000-281fffff
PREFETCH window: 28000000-280fffff
PCI: Bridge: 0000:00:1c.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.2 to 64
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1220837357.074:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 52394A11B61A91
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0x20000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x20b0-0x20b7, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Write protecting the kernel read-only data: 475k
input: AT Translated Set 2 keyboard as /class/input/input0
GSI 19 sharing vector 0xE1 and IRQ 19
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 225, io mem 0x282a4000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 225, io base 0x00002080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 185, io base 0x00002060
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-3: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 177, io base 0x00002040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 20 sharing vector 0xE9 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 233, io base 0x00002020
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-3: configuration #1 chosen from 1 choice
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x20c8 ctl 0x20ec bmdma 0x20a0 irq 185
ata2: SATA max UDMA/133 cmd 0x20c0 ctl 0x20e8 bmdma 0x20a8 irq 185
ata1.00: HPA detected: current 312579695, native 312581808
ata1.00: ATA-7: ST3160815AS, 3.AAD, max UDMA/133
ata1.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
Vendor: ATA Model: ST3160815AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: waiting for device to settle before scanning
Vendor: Kingston Model: DataTravelerMini Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 3915776 512-byte hdwr sectors (2005 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 3915776 512-byte hdwr sectors (2005 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1220837371.002:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
security: 3 users, 6 roles, 1676 types, 213 bools, 1 sens, 1024 cats
security: 61 classes, 60092 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1220837371.362:3): policy loaded auid=4294967295 ses=4294967295
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 185
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
r8168 Gigabit Ethernet driver 8.008.00-NAPI loaded
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:01:00.0 to 64
r8168: This product is covered by one or more of the following patents: US5,307,459, US5,434,872, US5,732,094, US6,570,884, US6,115,776, and US6,327,625.
eth0: Identified chip type is 'RTL8168C/8111C'.
eth0: RTL8168B/8111B at 0xffffc20000020000, 00:1c:c0:70:8f:f6, IRQ 50
input: PC Speaker as /class/input/input1
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
you are certain that your <4>intel_rng: system has a functional
RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
GSI 21 sharing vector 0x3A and IRQ 21
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1b.0 to 64
floppy0: no floppy controllers found
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1015800k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:1015800k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (2012 buckets, 16096 max) - 304 bytes per conntrack
r8168: eth0: link up
eth0: no IPv6 routers present
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 233
[drm] Initialized i915 1.8.0 20060929 on minor 0



----------------------------------------------------------------------------------------------
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
Subsystem: Intel Corporation Unknown device 464c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 233
Region 0: Memory at 28200000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 20e0 [size=8]
Region 2: Memory at 20000000 (32-bit, prefetchable) [size=128M]
Region 3: Memory at 28280000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: Intel Corporation Unknown device d604
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 58
Region 0: Memory at 282a0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)

00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 28100000-281fffff
Prefetchable memory behind bridge: 0000000028000000-0000000028000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40c9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40d1
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 4, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 40d9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 225
Region 4: I/O ports at 2080 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 185
Region 4: I/O ports at 2060 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 177
Region 4: I/O ports at 2040 [size=32]

00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 233
Region 4: I/O ports at 2020 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 225
Region 0: Memory at 282a4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]

00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 20b0 [size=16]

00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 185
Region 0: I/O ports at 20c8 [size=8]
Region 1: I/O ports at 20ec [size=4]
Region 2: I/O ports at 20c0 [size=8]
Region 3: I/O ports at 20e8 [size=4]
Region 4: I/O ports at 20a0 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: Intel Corporation Unknown device 464c
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 185
Region 4: I/O ports at 2000 [size=32]

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
Subsystem: Unknown device 8680:0100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: I/O ports at 1000 [size=256]
Region 2: Memory at 28100000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at 28000000 (64-bit, prefetchable) [size=64K]
Expansion ROM at 28020000 [disabled] [size=128K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee03000 Data: 4032
Capabilities: [70] Express Endpoint IRQ 1
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-01

Thanks; I've been leaning away from the VIA C7 to the Atom so it's nice to know that CentOS mostly works :).

Edit: Did you install from a SATA DVD drive? I'm wondering whether that will work, or if it needs to use PATA. I'm thinking of just buying one of the MSI Wind barebones desktop machines and they only have SATA as far as I can see.

I guess PATA or SATA would not matter. But in this case I installed from a PATA LG DVD drive.

Hello,

@zeehond: are you able to control speed of the fan installed on chipset?

I had no problem with recognising the sensor, but changing the value of speed control, ends without possitive result.

Hi folks,
I found this thread by searching for "Intel(R) Atom(TM) CPU 330 @ 1.60GHz" (extracted from dmidecode output).
I am having a bit of an issue with lm_sensors. All I get back from it is:
[root@acoustix ~]# sensors
smsc47m1-isa-0680
Adapter: ISA adapter
fan1: 1780 RPM (min = 1280 RPM, div = 4)
fan2: 7021 RPM (min = 1280 RPM, div = 4)

[root@acoustix ~]#

Sysinfo:
2.6.18-92.1.22.el5.centos.plus x86_64 GNU/Linux


I believe you guys got that working, right?
Any idea what my issues are?
Thanks in advance,

3KH

I ended up installing Ubuntu rather than CentOS on my Atom system as it's solely for MythTV, and lm-sensors on there definitely gives me temperature and voltage readings. So the latest versions of lm-sensors support it, but I don't know whether the CentOS version does.

More info than any human could possibly want on the RTL8111B/C issues:

http://wiki.centos.org/AdditionalResources/HardwareList/RealTekRTL8111b

Movieman,
Doing any hi-def MythTV on your Atom board? The video systems on the various mini-ITX boards has been a big question mark for me. Can it do 1920x1080 without hiccups?

No; unfortunately mplayer is still single-threaded when playing H.264, so it can't manage 1080 playback without dropping lots of frames. I don't think it will have a problem once they add multithreading support though, as it did fairly well with some 1080 files I downloaded; I don't know what codec those used, but I think it may have been Xvid. Well, technically I believe it can do multithreaded decoding of some types of H.264 files, but not the ones that I've been trying; I had one CPU at 85%, one at 6% and two at 0%.

I only had one 720p file (a movie trailer that I downloaded ages ago) and that did play OK.

Edit: the other issue is that the Intel video drivers don't currently support TV-out properly on Linux, but I'm going to plug it into an LCD TV via the VGA input so that doesn't really matter to me.

Bummer. Those mini-ITX boards sure look interesting. I guess it'll get there on the HD front eventually.

I believe there's a way to get a Windows multithreaded H.264 codec to run on Linux for 1080 playback on dual-core Atoms, but I haven't looked into that yet; I'm hoping that mplayer fixes their code before I have to! I don't think the single-cores have the CPU power to do more than 720, even multithreaded.

I have atom 1.6 and my cpu fan is allways on full speed ... is there a way to slow it down ?

Quote:

Atoms don't have CPU fans.

If you mean the chipset fan, the best solution is to either replace the heatsink with a better one, or replace the fan with something less noisy: I use one of these and it works fine:

http://www.ncix.com/products/index.php?sku=22361

Does the D945GCLF2's chipset support (supply) the HPET (High Precision Event Timer) as both the kernel and asterisk.

Your output shows...


I'd be curious to see the outputs from both



and



If so, is/are there any modifications needed from a standard Centos 5.3 ISO install.

I thinking of moving to this board as well. We do a fair bit of MeetMe conferencing and the better the timer source the better asterisk-everything works.

Thanks,

From the intel doc's, there is BIOS setting...



Not -- yet -- having one of these boards, this is the best I can offer.

The trick is to then see if CentOS "sees" it and uses it and then if asterisk does too.

/S

Not sure if there was a question about the CentOS kernel there but perhaps this will be useful to know --

I'm getting ATA subsystem errors when trying to install CentOS on the D945GCLF, the same board being discussed here but with an Atom 230, the single core version. Sorry I don't have exact transcripts of the error messages (they scroll by awfully quick), but I was able to capture the follow interesting bits with my camera:

----- snip! -----
status: { DRDY ERR }
error: { ICRC ABRT }
soft resetting link
failed to IDENTIFY (I/O error, err_mask=0x2)
revalidation failed (errno=-5)
failed to recover some devices, retrying in 5 secs
----- snip! -----

another part I was able to capture is:

----- snip!-----
soft resetting link
configured for UDMA/33 [Remember, this is a SATA bus]
EH complete
warning at drivers/ata/libata-sff.c:1317/ata_sff_hsm_move()

[Then the contents of a trace that are cut off]
----- snip! -----

If further details of these error messages will help debug, I'll go to greater length to provide the precise output of a dmesg.

I get these same messages with several different changes:
- CentOS 5.3 x86_64 or CentOS 5.0 i386 (the two DVDs I had already downloaded)
- Drives:
- 2x Western Digital Caviar Black 1TB SATA drives
- Each WD individually
- Seagate ST31000340NS ES.2 1TB (borrowed from work to see whether it was the WD drives causing the problem)
- I've swapped out several different SATA cables too
- Lite-On SOHD 16P9S DVD-ROM or NEC ND-1300A DVD-RW. Both are PATA
- GEIL 1GB DDR2 GX21GB5300X, or NANYA 512MB DDR2 NT512T64U88A0BY-37B (pulled from a Dell desktop)

No matter what I swap out, the error always happens.

About the only bits I haven't swapped out are:
- Motherboard/CPU
- Power Supply
- Chassis

I've done extensive Googling on these error messages with no luck, and looking for common problems with CentOS and Intel's Atom motherboards the only things I can find are about the network drivers.

Has anyone else had similar problems? Do I just have a bad mother board that needs to be replaced? Any help you can provide would be greatly appreciated. Thanks.

-Mark

If anyone else is interested. I have just installed CentOS 5.3 as a server on the Intel D945GCLF2(same), no issues so far. Sound driver problem seems to be fixed. After I install more, ill post if any issues.