Smstools and Huawei E173 modem
Posted: 2012/03/20 10:00:46
Hi,
I am trying to run smstools with my Huawei E173 modem bu no luck so far...
The modem is not even visible as /dev/ttyUSB*.
Can you advise how I should proceed? When I try to send any SMS I have messages as per below (in my /var/log/smsd/smsd.log)
[code]
2012-03-20 10:40:22,7, GSM1: ->
2012-03-20 10:40:22,3, GSM1: Could not send character , cause: Input/output error
2012-03-20 10:40:43,2, smsd: Smsd v2.2.20 started.
2012-03-20 10:40:43,6, smsd: outgoing file checker has started.
2012-03-20 10:40:43,6, GSM1: Modem handler 0 has started.
2012-03-20 10:40:43,3, GSM1: Cannot open serial port, cause: No such file or directory
2012-03-20 10:40:43,2, GSM1: Modem handler 0 terminated.
2012-03-20 10:42:24,6, smsd: Moved file /var/spool/sms/outgoing/send_HhGEoU to /var/spool/sms/checked
[/code]
My /etc/smsd.conf lookes like this
[code]
# Example smsd.conf. Read the manual for a description
devices = GSM1
logfile = /var/log/smsd/smsd.log
loglevel = 7
user = smstools
# 3.1.5 introduced smart logging
# once your configuration is OK, set log level lower (5 is good in most cases)
smart_logging = yes
[GSM1]
device = /dev/ttyUSB1
incoming = yes
#pin = 1111
[/code]
Thanks in advance.
I am trying to run smstools with my Huawei E173 modem bu no luck so far...
The modem is not even visible as /dev/ttyUSB*.
Can you advise how I should proceed? When I try to send any SMS I have messages as per below (in my /var/log/smsd/smsd.log)
[code]
2012-03-20 10:40:22,7, GSM1: ->
2012-03-20 10:40:22,3, GSM1: Could not send character , cause: Input/output error
2012-03-20 10:40:43,2, smsd: Smsd v2.2.20 started.
2012-03-20 10:40:43,6, smsd: outgoing file checker has started.
2012-03-20 10:40:43,6, GSM1: Modem handler 0 has started.
2012-03-20 10:40:43,3, GSM1: Cannot open serial port, cause: No such file or directory
2012-03-20 10:40:43,2, GSM1: Modem handler 0 terminated.
2012-03-20 10:42:24,6, smsd: Moved file /var/spool/sms/outgoing/send_HhGEoU to /var/spool/sms/checked
[/code]
My /etc/smsd.conf lookes like this
[code]
# Example smsd.conf. Read the manual for a description
devices = GSM1
logfile = /var/log/smsd/smsd.log
loglevel = 7
user = smstools
# 3.1.5 introduced smart logging
# once your configuration is OK, set log level lower (5 is good in most cases)
smart_logging = yes
[GSM1]
device = /dev/ttyUSB1
incoming = yes
#pin = 1111
[/code]
Thanks in advance.