Centos 6.2 USB issue

General support questions
Post Reply
171165312
Posts: 3
Joined: 2012/03/31 12:52:23

Centos 6.2 USB issue

Post by 171165312 » 2012/03/31 13:17:10

I currently have an Asus core i7 running both Windows 7 Premium and Centos 6.2 (Red Hat).
It comes with 8 USB ports (6 USB 2.0 and 2 USB 3.0).
I'm attempting to connect a gaming device (Novint Falcon), which requires USB 2.0 as a minimum.
It works as expected under Windows 7.
However, under Linux, all USB ports are detected as USB 1.1 even though lsmod indicates that xhci_hcd (which in theory is the module for USB 3.0) is mounted.
I have tried altering the BIOS USB settings with all possible combinations - disabling/enabling USB 3.0, disabling/enabling USB 2.0 support, etc.
I also tried using "modprobe -r xhci_hcd" and "modprobe -a ehci_hcd" with terminal (this failed miserably as the system indicates that ehci_hcd cannot be found. Furthermore, after xhci_hcd was disabled, no USB modules, ehci uhci or ohci, were detected, so I don't even know why my mouse and keyboard still functioned properly).
Not too surprisingly, the driver for Novint Falcon fails because USB 1.1 does not meet the minimum requirement.
Any suggestions as to what I could try to resolve this other than running it in Windows?

pschaff
Retired Moderator
Posts: 18276
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America
Contact:

Centos 6.2 USB issue

Post by pschaff » 2012/03/31 16:00:42

Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature, and [url=http://www.centos.org/modules/newbb/viewtopic.php?topic_id=28723&forum=54]provide more information about your system[/url] by running "./getinfo.sh" and showing us the output file.

171165312
Posts: 3
Joined: 2012/03/31 12:52:23

Re: Centos 6.2 USB issue

Post by 171165312 » 2012/04/02 22:54:00

[quote]
pschaff wrote:
Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature, and [url=http://www.centos.org/modules/newbb/viewtopic.php?topic_id=28723&forum=54]provide more information about your system[/url] by running "./getinfo.sh" and showing us the output file.[/quote]

Thanks for the tips, I have included my system information below:
Information for general problems.
[code]
== BEGIN uname -rmi ==
2.6.32-220.el6.x86_64 x86_64 x86_64
== END uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
centos-release-6-2.el6.centos.7.x86_64
adobe-release-x86_64-1.0-1.noarch
== END rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END cat /etc/redhat-release ==

== BEGIN getenforce ==
Enforcing
== END getenforce ==

== BEGIN free -m ==
total used free shared buffers cached
Mem: 24022 1021 23000 0 22 370
-/+ buffers/cache: 628 23393
Swap: 26207 0 26207
== END free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.x86_64
rpm-libs-4.8.0-19.el6.x86_64
rpm-python-4.8.0-19.el6.x86_64
yum-3.2.29-22.el6.centos.2.noarch
yum-metadata-parser-1.1.2-16.el6.x86_64
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
== END rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
adobe-linux-x86_64.repo
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
google-chrome.repo
== END ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

# This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
# It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit
Loading mirror speeds from cached hostfile
* base: mirrors.kernel.org
* extras: mirrors.kernel.org
* updates: mirror.stanford.edu
repo id repo name status
adobe-linux-x86_64 Adobe Systems Incorporated enabled: 2
base CentOS-6 - Base enabled: 6,294
c6-media CentOS-6 - Media disabled
centosplus CentOS-6 - Plus disabled
contrib CentOS-6 - Contrib disabled
debug CentOS-6 - Debuginfo disabled
extras CentOS-6 - Extras enabled: 4
google-chrome google-chrome enabled: 3
updates CentOS-6 - Updates enabled: 652
repolist: 6,955
== END yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
== END egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==

#
# /etc/fstab
# Created by anaconda on Fri Mar 16 10:10:43 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
/dev/mapper/vg_frank-lv_root / ext4 defaults 1 1
UUID=9a19b497-7464-44e2-9e41-f42a781170e3 /boot ext4 defaults 1 2
/dev/mapper/vg_frank-lv_home /home ext4 defaults 1 2
/dev/mapper/vg_frank-lv_swap swap swap defaults 0 0
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
== END cat /etc/fstab ==

== BEGIN df -h ==
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_frank-lv_root
50G 4.3G 43G 10% /
tmpfs 12G 272K 12G 1% /dev/shm
/dev/sda1 485M 88M 372M 20% /boot
/dev/mapper/vg_frank-lv_home
1.3T 198M 1.3T 1% /home
== END df -h ==

== BEGIN fdisk -l ==
Disk /dev/mapper/vg_frank-lv_root doesn't contain a valid partition table
Disk /dev/mapper/vg_frank-lv_swap doesn't contain a valid partition table
Disk /dev/mapper/vg_frank-lv_home doesn't contain a valid partition table

Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0004a8e3

Device Boot Start End Blocks Id System

Disk /dev/sda: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00012434

Device Boot Start End Blocks Id System
/dev/sda1 * 1 64 512000 83 Linux
Partition 1 does not end on cylinder boundary.
/dev/sda2 64 182402 1464625152 8e Linux LVM

Disk /dev/sdb: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xa4a18eec

Device Boot Start End Blocks Id System
/dev/sdb1 * 1 13 102400 7 HPFS/NTFS
Partition 1 does not end on cylinder boundary.
/dev/sdb2 13 14594 117115904 7 HPFS/NTFS

Disk /dev/mapper/vg_frank-lv_root: 53.7 GB, 53687091200 bytes
255 heads, 63 sectors/track, 6527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000


Disk /dev/mapper/vg_frank-lv_swap: 27.5 GB, 27481079808 bytes
255 heads, 63 sectors/track, 3341 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000


Disk /dev/mapper/vg_frank-lv_home: 1418.6 GB, 1418605887488 bytes
255 heads, 63 sectors/track, 172469 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

== END fdisk -l ==

== BEGIN parted -l ==
Model: ATA WDC WD1503FYYS-0 (scsi)
Disk /dev/sda: 1500GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number Start End Size Type File system Flags
1 1049kB 525MB 524MB primary ext4 boot
2 525MB 1500GB 1500GB primary lvm


Model: ATA INTEL SSDSA2M120 (scsi)
Disk /dev/sdb: 120GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number Start End Size Type File system Flags
1 1049kB 106MB 105MB primary ntfs boot
2 106MB 120GB 120GB primary ntfs


Model: ATA WDC WD1503FYYS-0 (scsi)
Disk /dev/sdc: 1500GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number Start End Size Type File system Flags


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_home: 1419GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number Start End Size File system Flags
1 0.00B 1419GB 1419GB ext4


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_swap: 27.5GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number Start End Size File system Flags
1 0.00B 27.5GB 27.5GB linux-swap(v1)


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_root: 53.7GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number Start End Size File system Flags
1 0.00B 53.7GB 53.7GB ext4


== END parted -l ==

== BEGIN blkid ==
/dev/sda1: UUID="9a19b497-7464-44e2-9e41-f42a781170e3" TYPE="ext4"
/dev/sda2: UUID="6mvZod-gOAa-yVm3-JeMN-yTHw-hnh8-1nVdnt" TYPE="LVM2_member"
/dev/sdb1: LABEL="System Reserved" UUID="00EEBC41EEBC30B0" TYPE="ntfs"
/dev/sdb2: UUID="8C7A3A417A3A27FA" TYPE="ntfs"
/dev/mapper/vg_frank-lv_root: UUID="e827b386-5925-4ee4-9878-f78e02389d29" TYPE="ext4"
/dev/mapper/vg_frank-lv_swap: UUID="dfe06fd5-d2e2-4334-bddf-1a6ee1359fcd" TYPE="swap"
/dev/mapper/vg_frank-lv_home: UUID="8e74bd2e-fc5c-4c9c-98b8-abf8522b223a" TYPE="ext4"
== END blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END cat /proc/mdstat ==

== BEGIN pvs ==
PV VG Fmt Attr PSize PFree
/dev/sda2 vg_frank lvm2 a-- 1.36t 0
== END pvs ==

== BEGIN vgs ==
VG #PV #LV #SN Attr VSize VFree
vg_frank 1 3 0 wz--n- 1.36t 0
== END vgs ==

== BEGIN lvs ==
LV VG Attr LSize Origin Snap% Move Log Copy% Convert
lv_home vg_frank -wi-ao 1.29t
lv_root vg_frank -wi-ao 50.00g
lv_swap vg_frank -wi-ao 25.59g
== END lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.el6.x86_64
kernel-devel-2.6.32-220.7.1.el6.x86_64
kernel-firmware-2.6.32-220.el6.noarch
kernel-headers-2.6.32-220.7.1.el6.x86_64
== END rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port [8086:3405] (rev 13)
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 13)
00:02.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 [8086:3409] (rev 13)
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 13)
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 [8086:340e] (rev 13)
00:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers [8086:342e] (rev 13)
00:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers [8086:3422] (rev 13)
00:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers [8086:3423] (rev 13)
00:14.3 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers [8086:3438] (rev 13)
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37]
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38]
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39]
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c]
00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller [8086:3a3e]
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 [8086:3a40]
00:1c.2 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 [8086:3a44]
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 [8086:3a4a]
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34]
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35]
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36]
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a]
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller [8086:3a16]
00:1f.2 RAID bus controller [0104]: Intel Corporation 82801 SATA Controller [RAID mode] [8086:2822]
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller [8086:3a30]
03:00.0 VGA compatible controller [0300]: nVidia Corporation GF100 [Quadro 5000] [10de:06d9] (rev a3)
03:00.1 Audio device [0403]: nVidia Corporation GF100 High Definition Audio Controller [10de:0be5] (rev a1)
04:00.0 VGA compatible controller [0300]: nVidia Corporation GF100 [Tesla C2050 / C2070] [10de:06d1] (rev a3)
04:00.1 Audio device [0403]: nVidia Corporation GF100 High Definition Audio Controller [10de:0be5] (rev a1)
05:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12)
06:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12)
08:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0)
== END lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 2222:3100 MacAlly
Bus 007 Device 002: ID 046d:0b04 Logitech, Inc.
Bus 007 Device 003: ID 046d:c713 Logitech, Inc.
Bus 007 Device 004: ID 046d:c714 Logitech, Inc. diNovo Edge Keyboard
== END lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
== END rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0 Link encap:Ethernet HWaddr 20:CF:30:6C:1A:CE
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:18

eth1 Link encap:Ethernet HWaddr 20:CF:30:6C:16:DE
inet addr:171.64.125.193 Bcast:171.64.125.255 Mask:255.255.254.0
inet6 addr: fe80::22cf:30ff:fe6c:16de/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3363 errors:0 dropped:0 overruns:0 frame:0
TX packets:2181 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1685489 (1.6 MiB) TX bytes:337988 (330.0 KiB)
Interrupt:17

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:22 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1788 (1.7 KiB) TX bytes:1788 (1.7 KiB)

== END ifconfig -a ==

== BEGIN brctl show ==
./getinfo.sh: line 87: brctl: command not found
== END brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
171.64.124.0 0.0.0.0 255.255.254.0 U 1 0 0 eth1
0.0.0.0 171.64.124.1 0.0.0.0 UG 0 0 0 eth1
== END route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
domain Stanford.EDU
search Stanford.EDU
nameserver 171.64.7.55
nameserver 171.64.7.121
nameserver 171.64.7.99
== END cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks: nisplus [NOTFOUND=return] files
#netmasks: nisplus [NOTFOUND=return] files
netmasks: files
networks: files
netgroup: nisplus
== END grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager 0:off 1:off 2:on 3:on 4:on 5:on 6:off
matahari-network 0:off 1:off 2:off 3:off 4:off 5:off 6:off
network 0:off 1:off 2:on 3:on 4:on 5:on 6:off
wpa_supplicant 0:off 1:off 2:off 3:off 4:off 5:off 6:off
== END chkconfig --list | grep -Ei 'network|wpa' ==

[/code]

171165312
Posts: 3
Joined: 2012/03/31 12:52:23

Re: Centos 6.2 USB issue

Post by 171165312 » 2012/04/02 23:11:21

For the lsusb part, Bus 003-008 are the external usb ports. Although Bus 001 and 002 are indicated as USB 2.0, I am unable to connect to either of them.

pschaff
Retired Moderator
Posts: 18276
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America
Contact:

Re: Centos 6.2 USB issue

Post by pschaff » 2012/04/03 01:15:57

Is it possible that those are motherboard header connectors that are not externally available?

A "yum update" and reboot is worth a try as you are still running the problematic original 6.2 kernel, although kernel-devel and kernel-headers are current. I see no reason that would happen unless the kernel was explicitly not updated.

martijnv
Posts: 1
Joined: 2012/04/06 20:47:19

Re: Centos 6.2 USB issue

Post by martijnv » 2012/04/06 20:57:13

I have installed the latest PBX in a Flash distro which includes CentOS 6.2 and I have the same problem as the topic starter. Did you resolve the problem? Here is my info:

Information for general problems.
[code]
== BEGIN uname -rmi ==
2.6.32-220.7.1.el6.i686 i686 i386
== END uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
centos-release-6-2.el6.centos.7.i686
== END rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END cat /etc/redhat-release ==

== BEGIN getenforce ==
Disabled
== END getenforce ==

== BEGIN free -m ==
total used free shared buffers cached
Mem: 3916 464 3452 0 24 205
-/+ buffers/cache: 233 3682
Swap: 766 0 766
== END free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.i686
rpm-build-4.8.0-19.el6_2.1.i686
rpm-libs-4.8.0-19.el6_2.1.i686
rpm-python-4.8.0-19.el6_2.1.i686
yum-3.2.29-22.el6.centos.2.noarch
yum-metadata-parser-1.1.2-16.el6.i686
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
yum-utils-1.1.30-10.el6.noarch
== END rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
piaf.repo
webmin.repo
== END ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

# This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
# It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit
Loading mirror speeds from cached hostfile
* Webmin: webmin.mirror.somersettechsolutions.co.uk
* base: centos.mirror.transip.nl
* extras: centos.mirror.transip.nl
* updates: centos.mirror.transip.nl
repo id repo name status
Webmin Webmin Distribution Neutral enabled: 102
base CentOS-6 - Base enabled: 4,757+7
c6-media CentOS-6 - Media disabled
centosplus CentOS-6 - Plus disabled
contrib CentOS-6 - Contrib disabled
debug CentOS-6 - Debuginfo disabled
extras CentOS-6 - Extras enabled: 4
incredible INCREDIBLE 6 - i386 disabled
incredreq INCREDIBLE REQUIRED 6 - i386 disabled
incredreq-source INCREDIBLE-REQUIRED 6 - i386 - Source disabled
piaf PIAF 6 - i386 disabled
piaf6 PIAF6 6 - i386 disabled
tatic TATIC 6 - i386 disabled
tatic-source TATIC Repository 6 - i386 - Source disabled
updates CentOS-6 - Updates enabled: 484+28
repolist: 5,347
== END yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/piaf.repo:#packages have been excluded from the CentOS repo to prevent conflicts.
== END egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==

#
# /etc/fstab
# Created by anaconda on Thu Apr 5 10:23:24 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=dd9be61a-56ab-4144-b2d5-9347b46841f4 / ext3 defaults 1 1
UUID=80d75362-66ee-4591-b418-334527cce6d8 /boot ext3 defaults 1 2
UUID=fea32d06-0445-4b53-915f-72ee18662a71 swap swap defaults 0 0
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
== END cat /etc/fstab ==

== BEGIN df -h ==
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 55G 3.6G 48G 7% /
tmpfs 2.0G 0 2.0G 0% /dev/shm
/dev/sda1 97M 29M 64M 31% /boot
== END df -h ==

== BEGIN fdisk -l ==

Disk /dev/sda: 60.0 GB, 60022480896 bytes
255 heads, 63 sectors/track, 7297 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0002f8b0

Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 102400 83 Linux
Partition 1 does not end on cylinder boundary.
/dev/sda2 13 7200 57725952 83 Linux
/dev/sda3 7200 7298 785408 82 Linux swap / Solaris
== END fdisk -l ==

== BEGIN parted -l ==
Model: ATA OCZ-VERTEX2 (scsi)
Disk /dev/sda: 60.0GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number Start End Size Type File system Flags
1 1049kB 106MB 105MB primary ext3 boot
2 106MB 59.2GB 59.1GB primary ext3
3 59.2GB 60.0GB 804MB primary linux-swap(v1)


== END parted -l ==

== BEGIN blkid ==
/dev/sda1: UUID="80d75362-66ee-4591-b418-334527cce6d8" TYPE="ext3"
/dev/sda2: UUID="dd9be61a-56ab-4144-b2d5-9347b46841f4" TYPE="ext3"
/dev/sda3: UUID="fea32d06-0445-4b53-915f-72ee18662a71" TYPE="swap"
== END blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END cat /proc/mdstat ==

== BEGIN pvs ==
== END pvs ==

== BEGIN vgs ==
No volume groups found
== END vgs ==

== BEGIN lvs ==
No volume groups found
== END lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.7.1.el6.i686
kernel-devel-2.6.32-220.7.1.el6.i686
kernel-firmware-2.6.32-220.7.1.el6.noarch
kernel-headers-2.6.32-220.7.1.el6.i686
== END rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a000] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a001] (rev 02)
00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a002] (rev 02)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02)
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02)
00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02)
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02)
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02)
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02)
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02)
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2)
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02)
02:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2382] (rev 80)
02:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2381] (rev 80)
02:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2383] (rev 80)
02:00.5 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 03)
== END lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 014: ID e4e4:1162 Xorcom Ltd. Astribank 2 series
Bus 004 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
== END lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
== END rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0 Link encap:Ethernet HWaddr 80:EE:73:1E:AA:B7
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::82ee:73ff:fe1e:aab7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4029 errors:0 dropped:0 overruns:0 frame:0
TX packets:2834 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:647487 (632.3 KiB) TX bytes:1280293 (1.2 MiB)
Interrupt:29

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3373 errors:0 dropped:0 overruns:0 frame:0
TX packets:3373 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:668542 (652.8 KiB) TX bytes:668542 (652.8 KiB)

== END ifconfig -a ==

== BEGIN brctl show ==
bridge name bridge id STP enabled interfaces
== END brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0
0.0.0.0 192.168.0.100 0.0.0.0 UG 0 0 0 eth0
== END route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
nameserver 192.168.0.100
== END cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks: nisplus [NOTFOUND=return] files
#netmasks: nisplus [NOTFOUND=return] files
netmasks: files
networks: files
netgroup: nisplus
== END grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager 0:off 1:off 2:off 3:off 4:off 5:off 6:off
network 0:off 1:off 2:on 3:on 4:on 5:on 6:off
wpa_supplicant 0:off 1:off 2:off 3:off 4:off 5:off 6:off
== END chkconfig --list | grep -Ei 'network|wpa' ==

[/code]

pschaff
Retired Moderator
Posts: 18276
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America
Contact:

Re: Centos 6.2 USB issue

Post by pschaff » 2012/04/06 21:13:04

Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature.

[url=http://wiki.centos.org/AdditionalResources/OtherVoices#line-70]PIAF[/url] is one of those not-CentOS distros that it is hard for us to support, as attested to by the repo configs and excludes therein; but in any case, after reading the recommended links you should realize why you should not hijack threads as you have done. Please start a new Topic for your issue to get the attention you need, providing a link to this one if required for context.

Post Reply