Centos 6.2 USB issue

General support questions

Centos 6.2 USB issue

Postby 171165312 » 2012/03/31 13:17:10

I currently have an Asus core i7 running both Windows 7 Premium and Centos 6.2 (Red Hat).
It comes with 8 USB ports (6 USB 2.0 and 2 USB 3.0).
I'm attempting to connect a gaming device (Novint Falcon), which requires USB 2.0 as a minimum.
It works as expected under Windows 7.
However, under Linux, all USB ports are detected as USB 1.1 even though lsmod indicates that xhci_hcd (which in theory is the module for USB 3.0) is mounted.
I have tried altering the BIOS USB settings with all possible combinations - disabling/enabling USB 3.0, disabling/enabling USB 2.0 support, etc.
I also tried using "modprobe -r xhci_hcd" and "modprobe -a ehci_hcd" with terminal (this failed miserably as the system indicates that ehci_hcd cannot be found. Furthermore, after xhci_hcd was disabled, no USB modules, ehci uhci or ohci, were detected, so I don't even know why my mouse and keyboard still functioned properly).
Not too surprisingly, the driver for Novint Falcon fails because USB 1.1 does not meet the minimum requirement.
Any suggestions as to what I could try to resolve this other than running it in Windows?
171165312
 
Posts: 3
Joined: 2012/03/31 12:52:23

Centos 6.2 USB issue

Postby pschaff » 2012/03/31 16:00:42

Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature, and provide more information about your system by running "./getinfo.sh" and showing us the output file.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Centos 6.2 USB issue

Postby 171165312 » 2012/04/02 22:54:00

pschaff wrote:
Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature, and provide more information about your system by running "./getinfo.sh" and showing us the output file.


Thanks for the tips, I have included my system information below:
Information for general problems.
Code: Select all
== BEGIN uname -rmi ==
2.6.32-220.el6.x86_64 x86_64 x86_64
== END   uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
centos-release-6-2.el6.centos.7.x86_64
adobe-release-x86_64-1.0-1.noarch
== END   rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END   cat /etc/redhat-release ==

== BEGIN getenforce ==
Enforcing
== END   getenforce ==

== BEGIN free -m ==
             total       used       free     shared    buffers     cached
Mem:         24022       1021      23000          0         22        370
-/+ buffers/cache:        628      23393
Swap:        26207          0      26207
== END   free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.x86_64
rpm-libs-4.8.0-19.el6.x86_64
rpm-python-4.8.0-19.el6.x86_64
yum-3.2.29-22.el6.centos.2.noarch
yum-metadata-parser-1.1.2-16.el6.x86_64
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
== END   rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
adobe-linux-x86_64.repo
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
google-chrome.repo
== END   ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

#  This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
#  It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END   cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit
Loading mirror speeds from cached hostfile
 * base: mirrors.kernel.org
 * extras: mirrors.kernel.org
 * updates: mirror.stanford.edu
repo id                      repo name                            status
adobe-linux-x86_64           Adobe Systems Incorporated           enabled:     2
base                         CentOS-6 - Base                      enabled: 6,294
c6-media                     CentOS-6 - Media                     disabled
centosplus                   CentOS-6 - Plus                      disabled
contrib                      CentOS-6 - Contrib                   disabled
debug                        CentOS-6 - Debuginfo                 disabled
extras                       CentOS-6 - Extras                    enabled:     4
google-chrome                google-chrome                        enabled:     3
updates                      CentOS-6 - Updates                   enabled:   652
repolist: 6,955
== END   yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
== END   egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END   sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==

#
# /etc/fstab
# Created by anaconda on Fri Mar 16 10:10:43 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
/dev/mapper/vg_frank-lv_root /                       ext4    defaults        1 1
UUID=9a19b497-7464-44e2-9e41-f42a781170e3 /boot                   ext4    defaults        1 2
/dev/mapper/vg_frank-lv_home /home                   ext4    defaults        1 2
/dev/mapper/vg_frank-lv_swap swap                    swap    defaults        0 0
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
== END   cat /etc/fstab ==

== BEGIN df -h ==
Filesystem            Size  Used Avail Use% Mounted on
/dev/mapper/vg_frank-lv_root
                       50G  4.3G   43G  10% /
tmpfs                  12G  272K   12G   1% /dev/shm
/dev/sda1             485M   88M  372M  20% /boot
/dev/mapper/vg_frank-lv_home
                      1.3T  198M  1.3T   1% /home
== END   df -h ==

== BEGIN fdisk -l ==
Disk /dev/mapper/vg_frank-lv_root doesn't contain a valid partition table
Disk /dev/mapper/vg_frank-lv_swap doesn't contain a valid partition table
Disk /dev/mapper/vg_frank-lv_home doesn't contain a valid partition table

Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0004a8e3

   Device Boot      Start         End      Blocks   Id  System

Disk /dev/sda: 1500.3 GB, 1500301910016 bytes
255 heads, 63 sectors/track, 182401 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00012434

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1          64      512000   83  Linux
Partition 1 does not end on cylinder boundary.
/dev/sda2              64      182402  1464625152   8e  Linux LVM

Disk /dev/sdb: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xa4a18eec

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *           1          13      102400    7  HPFS/NTFS
Partition 1 does not end on cylinder boundary.
/dev/sdb2              13       14594   117115904    7  HPFS/NTFS

Disk /dev/mapper/vg_frank-lv_root: 53.7 GB, 53687091200 bytes
255 heads, 63 sectors/track, 6527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000


Disk /dev/mapper/vg_frank-lv_swap: 27.5 GB, 27481079808 bytes
255 heads, 63 sectors/track, 3341 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000


Disk /dev/mapper/vg_frank-lv_home: 1418.6 GB, 1418605887488 bytes
255 heads, 63 sectors/track, 172469 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

== END   fdisk -l ==

== BEGIN parted -l ==
Model: ATA WDC WD1503FYYS-0 (scsi)
Disk /dev/sda: 1500GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start   End     Size    Type     File system  Flags
 1      1049kB  525MB   524MB   primary  ext4         boot
 2      525MB   1500GB  1500GB  primary               lvm


Model: ATA INTEL SSDSA2M120 (scsi)
Disk /dev/sdb: 120GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start   End    Size   Type     File system  Flags
 1      1049kB  106MB  105MB  primary  ntfs         boot
 2      106MB   120GB  120GB  primary  ntfs


Model: ATA WDC WD1503FYYS-0 (scsi)
Disk /dev/sdc: 1500GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start  End  Size  Type  File system  Flags


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_home: 1419GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number  Start  End     Size    File system  Flags
 1      0.00B  1419GB  1419GB  ext4


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_swap: 27.5GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number  Start  End     Size    File system     Flags
 1      0.00B  27.5GB  27.5GB  linux-swap(v1)


Model: Linux device-mapper (linear) (dm)
Disk /dev/mapper/vg_frank-lv_root: 53.7GB
Sector size (logical/physical): 512B/512B
Partition Table: loop

Number  Start  End     Size    File system  Flags
 1      0.00B  53.7GB  53.7GB  ext4


== END   parted -l ==

== BEGIN blkid ==
/dev/sda1: UUID="9a19b497-7464-44e2-9e41-f42a781170e3" TYPE="ext4"
/dev/sda2: UUID="6mvZod-gOAa-yVm3-JeMN-yTHw-hnh8-1nVdnt" TYPE="LVM2_member"
/dev/sdb1: LABEL="System Reserved" UUID="00EEBC41EEBC30B0" TYPE="ntfs"
/dev/sdb2: UUID="8C7A3A417A3A27FA" TYPE="ntfs"
/dev/mapper/vg_frank-lv_root: UUID="e827b386-5925-4ee4-9878-f78e02389d29" TYPE="ext4"
/dev/mapper/vg_frank-lv_swap: UUID="dfe06fd5-d2e2-4334-bddf-1a6ee1359fcd" TYPE="swap"
/dev/mapper/vg_frank-lv_home: UUID="8e74bd2e-fc5c-4c9c-98b8-abf8522b223a" TYPE="ext4"
== END   blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END   cat /proc/mdstat ==

== BEGIN pvs ==
  PV         VG       Fmt  Attr PSize PFree
  /dev/sda2  vg_frank lvm2 a--  1.36t    0
== END   pvs ==

== BEGIN vgs ==
  VG       #PV #LV #SN Attr   VSize VFree
  vg_frank   1   3   0 wz--n- 1.36t    0
== END   vgs ==

== BEGIN lvs ==
  LV      VG       Attr   LSize  Origin Snap%  Move Log Copy%  Convert
  lv_home vg_frank -wi-ao  1.29t                                     
  lv_root vg_frank -wi-ao 50.00g                                     
  lv_swap vg_frank -wi-ao 25.59g                                     
== END   lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.el6.x86_64
kernel-devel-2.6.32-220.7.1.el6.x86_64
kernel-firmware-2.6.32-220.el6.noarch
kernel-headers-2.6.32-220.7.1.el6.x86_64
== END   rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port [8086:3405] (rev 13)
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 13)
00:02.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 [8086:3409] (rev 13)
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 13)
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 [8086:340e] (rev 13)
00:14.0 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers [8086:342e] (rev 13)
00:14.1 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers [8086:3422] (rev 13)
00:14.2 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers [8086:3423] (rev 13)
00:14.3 PIC [0800]: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers [8086:3438] (rev 13)
00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37]
00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38]
00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39]
00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c]
00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller [8086:3a3e]
00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 [8086:3a40]
00:1c.2 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 [8086:3a44]
00:1c.5 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 [8086:3a4a]
00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34]
00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35]
00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36]
00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a]
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller [8086:3a16]
00:1f.2 RAID bus controller [0104]: Intel Corporation 82801 SATA Controller [RAID mode] [8086:2822]
00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller [8086:3a30]
03:00.0 VGA compatible controller [0300]: nVidia Corporation GF100 [Quadro 5000] [10de:06d9] (rev a3)
03:00.1 Audio device [0403]: nVidia Corporation GF100 High Definition Audio Controller [10de:0be5] (rev a1)
04:00.0 VGA compatible controller [0300]: nVidia Corporation GF100 [Tesla C2050 / C2070] [10de:06d1] (rev a3)
04:00.1 Audio device [0403]: nVidia Corporation GF100 High Definition Audio Controller [10de:0be5] (rev a1)
05:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12)
06:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12)
08:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0)
== END   lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 2222:3100 MacAlly
Bus 007 Device 002: ID 046d:0b04 Logitech, Inc.
Bus 007 Device 003: ID 046d:c713 Logitech, Inc.
Bus 007 Device 004: ID 046d:c714 Logitech, Inc. diNovo Edge Keyboard
== END   lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
== END   rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0      Link encap:Ethernet  HWaddr 20:CF:30:6C:1A:CE 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:18

eth1      Link encap:Ethernet  HWaddr 20:CF:30:6C:16:DE 
          inet addr:171.64.125.193  Bcast:171.64.125.255  Mask:255.255.254.0
          inet6 addr: fe80::22cf:30ff:fe6c:16de/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3363 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2181 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1685489 (1.6 MiB)  TX bytes:337988 (330.0 KiB)
          Interrupt:17

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:22 errors:0 dropped:0 overruns:0 frame:0
          TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1788 (1.7 KiB)  TX bytes:1788 (1.7 KiB)

== END   ifconfig -a ==

== BEGIN brctl show ==
./getinfo.sh: line 87: brctl: command not found
== END   brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
171.64.124.0    0.0.0.0         255.255.254.0   U     1      0        0 eth1
0.0.0.0         171.64.124.1    0.0.0.0         UG    0      0        0 eth1
== END   route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
domain Stanford.EDU
search Stanford.EDU
nameserver 171.64.7.55
nameserver 171.64.7.121
nameserver 171.64.7.99
== END   cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks:   nisplus [NOTFOUND=return] files
#netmasks:   nisplus [NOTFOUND=return] files     
netmasks:   files
networks:   files
netgroup:   nisplus
== END   grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager    0:off   1:off   2:on   3:on   4:on   5:on   6:off
matahari-network   0:off   1:off   2:off   3:off   4:off   5:off   6:off
network           0:off   1:off   2:on   3:on   4:on   5:on   6:off
wpa_supplicant    0:off   1:off   2:off   3:off   4:off   5:off   6:off
== END   chkconfig --list | grep -Ei 'network|wpa' ==

171165312
 
Posts: 3
Joined: 2012/03/31 12:52:23

Re: Centos 6.2 USB issue

Postby 171165312 » 2012/04/02 23:11:21

For the lsusb part, Bus 003-008 are the external usb ports. Although Bus 001 and 002 are indicated as USB 2.0, I am unable to connect to either of them.
171165312
 
Posts: 3
Joined: 2012/03/31 12:52:23

Re: Centos 6.2 USB issue

Postby pschaff » 2012/04/03 01:15:57

Is it possible that those are motherboard header connectors that are not externally available?

A "yum update" and reboot is worth a try as you are still running the problematic original 6.2 kernel, although kernel-devel and kernel-headers are current. I see no reason that would happen unless the kernel was explicitly not updated.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Centos 6.2 USB issue

Postby martijnv » 2012/04/06 20:57:13

I have installed the latest PBX in a Flash distro which includes CentOS 6.2 and I have the same problem as the topic starter. Did you resolve the problem? Here is my info:

Information for general problems.
Code: Select all
== BEGIN uname -rmi ==
2.6.32-220.7.1.el6.i686 i686 i386
== END   uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
centos-release-6-2.el6.centos.7.i686
== END   rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END   cat /etc/redhat-release ==

== BEGIN getenforce ==
Disabled
== END   getenforce ==

== BEGIN free -m ==
             total       used       free     shared    buffers     cached
Mem:          3916        464       3452          0         24        205
-/+ buffers/cache:        233       3682
Swap:          766          0        766
== END   free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.i686
rpm-build-4.8.0-19.el6_2.1.i686
rpm-libs-4.8.0-19.el6_2.1.i686
rpm-python-4.8.0-19.el6_2.1.i686
yum-3.2.29-22.el6.centos.2.noarch
yum-metadata-parser-1.1.2-16.el6.i686
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
yum-utils-1.1.30-10.el6.noarch
== END   rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
piaf.repo
webmin.repo
== END   ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

#  This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
#  It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END   cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit
Loading mirror speeds from cached hostfile
 * Webmin: webmin.mirror.somersettechsolutions.co.uk
 * base: centos.mirror.transip.nl
 * extras: centos.mirror.transip.nl
 * updates: centos.mirror.transip.nl
repo id              repo name                                  status
Webmin               Webmin Distribution Neutral                enabled:     102
base                 CentOS-6 - Base                            enabled: 4,757+7
c6-media             CentOS-6 - Media                           disabled
centosplus           CentOS-6 - Plus                            disabled
contrib              CentOS-6 - Contrib                         disabled
debug                CentOS-6 - Debuginfo                       disabled
extras               CentOS-6 - Extras                          enabled:       4
incredible           INCREDIBLE 6 - i386                        disabled
incredreq            INCREDIBLE REQUIRED 6 - i386               disabled
incredreq-source     INCREDIBLE-REQUIRED 6 - i386 - Source      disabled
piaf                 PIAF 6 - i386                              disabled
piaf6                PIAF6 6 - i386                             disabled
tatic                TATIC 6 - i386                             disabled
tatic-source         TATIC Repository 6 - i386 - Source         disabled
updates              CentOS-6 - Updates                         enabled:  484+28
repolist: 5,347
== END   yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/CentOS-Base.repo:exclude=kernel*
/etc/yum.repos.d/piaf.repo:#packages have been excluded from the CentOS repo to prevent conflicts.
== END   egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END   sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==

#
# /etc/fstab
# Created by anaconda on Thu Apr  5 10:23:24 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=dd9be61a-56ab-4144-b2d5-9347b46841f4 /                       ext3    defaults        1 1
UUID=80d75362-66ee-4591-b418-334527cce6d8 /boot                   ext3    defaults        1 2
UUID=fea32d06-0445-4b53-915f-72ee18662a71 swap                    swap    defaults        0 0
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
== END   cat /etc/fstab ==

== BEGIN df -h ==
Filesystem            Size  Used Avail Use% Mounted on
/dev/sda2              55G  3.6G   48G   7% /
tmpfs                 2.0G     0  2.0G   0% /dev/shm
/dev/sda1              97M   29M   64M  31% /boot
== END   df -h ==

== BEGIN fdisk -l ==

Disk /dev/sda: 60.0 GB, 60022480896 bytes
255 heads, 63 sectors/track, 7297 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0002f8b0

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1          13      102400   83  Linux
Partition 1 does not end on cylinder boundary.
/dev/sda2              13        7200    57725952   83  Linux
/dev/sda3            7200        7298      785408   82  Linux swap / Solaris
== END   fdisk -l ==

== BEGIN parted -l ==
Model: ATA OCZ-VERTEX2 (scsi)
Disk /dev/sda: 60.0GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos

Number  Start   End     Size    Type     File system     Flags
 1      1049kB  106MB   105MB   primary  ext3            boot
 2      106MB   59.2GB  59.1GB  primary  ext3
 3      59.2GB  60.0GB  804MB   primary  linux-swap(v1)


== END   parted -l ==

== BEGIN blkid ==
/dev/sda1: UUID="80d75362-66ee-4591-b418-334527cce6d8" TYPE="ext3"
/dev/sda2: UUID="dd9be61a-56ab-4144-b2d5-9347b46841f4" TYPE="ext3"
/dev/sda3: UUID="fea32d06-0445-4b53-915f-72ee18662a71" TYPE="swap"
== END   blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END   cat /proc/mdstat ==

== BEGIN pvs ==
== END   pvs ==

== BEGIN vgs ==
  No volume groups found
== END   vgs ==

== BEGIN lvs ==
  No volume groups found
== END   lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.7.1.el6.i686
kernel-devel-2.6.32-220.7.1.el6.i686
kernel-firmware-2.6.32-220.7.1.el6.noarch
kernel-headers-2.6.32-220.7.1.el6.i686
== END   rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a000] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a001] (rev 02)
00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a002] (rev 02)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02)
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02)
00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02)
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02)
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02)
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02)
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02)
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2)
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02)
02:00.0 System peripheral [0880]: JMicron Technology Corp. SD/MMC Host Controller [197b:2382] (rev 80)
02:00.2 SD Host controller [0805]: JMicron Technology Corp. Standard SD Host Controller [197b:2381] (rev 80)
02:00.3 System peripheral [0880]: JMicron Technology Corp. MS Host Controller [197b:2383] (rev 80)
02:00.5 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 03)
== END   lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 014: ID e4e4:1162 Xorcom Ltd. Astribank 2 series
Bus 004 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
== END   lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
== END   rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0      Link encap:Ethernet  HWaddr 80:EE:73:1E:AA:B7 
          inet addr:192.168.0.5  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::82ee:73ff:fe1e:aab7/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4029 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2834 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:647487 (632.3 KiB)  TX bytes:1280293 (1.2 MiB)
          Interrupt:29

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3373 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3373 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:668542 (652.8 KiB)  TX bytes:668542 (652.8 KiB)

== END   ifconfig -a ==

== BEGIN brctl show ==
bridge name   bridge id      STP enabled   interfaces
== END   brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 eth0
0.0.0.0         192.168.0.100   0.0.0.0         UG    0      0        0 eth0
== END   route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
nameserver 192.168.0.100
== END   cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks:   nisplus [NOTFOUND=return] files
#netmasks:   nisplus [NOTFOUND=return] files     
netmasks:   files
networks:   files
netgroup:   nisplus
== END   grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager    0:off   1:off   2:off   3:off   4:off   5:off   6:off
network           0:off   1:off   2:on   3:on   4:on   5:on   6:off
wpa_supplicant    0:off   1:off   2:off   3:off   4:off   5:off   6:off
== END   chkconfig --list | grep -Ei 'network|wpa' ==

martijnv
 
Posts: 1
Joined: 2012/04/06 20:47:19

Re: Centos 6.2 USB issue

Postby pschaff » 2012/04/06 21:13:04

Welcome to the CentOS fora. Please see the recommended reading for new users linked in my signature.

PIAF is one of those not-CentOS distros that it is hard for us to support, as attested to by the repo configs and excludes therein; but in any case, after reading the recommended links you should realize why you should not hijack threads as you have done. Please start a new Topic for your issue to get the attention you need, providing a link to this one if required for context.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America


Return to CentOS 6 - General Support

Who is online

Users browsing this forum: No registered users and 13 guests