[SOLVED] CentOS 6.0 LAN Atheros AR8151 problem

Issues related to hardware problems

[SOLVED] CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/10 23:04:04

Hi there,
i have been upgraded from CentOS 5 to 6, but i discovered this problem, my NIC is Atheros AR8151, and i can't start network.
So i had installed this package kmod-atl1e-1.0.1.14-1.el6.elrepo.x86_64.rpm but no thing change.

so what can i do ?
Thanks
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/12 00:40:41

Any help for this problem !!
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby AlanBartlett » 2012/02/12 13:31:48

Please determine the Vendor:Device ID Paring for the device by executing lspci -nn and posting the one line output that is relevant to it.
User avatar
AlanBartlett
Forum Moderator
 
Posts: 8975
Joined: 2007/10/22 11:30:09
Location: ~/Earth/UK/England/Suffolk

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/12 15:27:49

Thanks for replay, and that is the output:

Code: Select all
02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v1.0 Gigabit Ethernet [1969:1073] (rev c0)
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

[SOLVED] CentOS 6.0 LAN Atheros AR8151 problem

Postby pschaff » 2012/02/12 17:31:48

Checking the ELRepo DeviceIDs page shows that the kmod-atl1e driver should be appropriate for your hardware. It would have been preferable to install the current release, CentOS 6.2, and a "yum update" is advisable to get to that release level as soon as you get networking working.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/12 20:31:23

Checking the ELRepo DeviceIDs page shows that the kmod-atl1e driver should be appropriate for your hardware. It would have been preferable to install the current release, CentOS 6.2, and a "yum update" is advisable to get to that release level as soon as you get networking working.


Thanks for replay, but i had installed this package kmod-atl1e-1.0.1.14-1.el6.elrepo.x86_64.rpm but no thing change.
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby pschaff » 2012/02/12 22:40:43

Did you reboot after installing the kmod driver? That should not be strictly necessary but may be the best way to ensure that it is used.

If more help is needed then please provide more information about your system by running "./getinfo.sh" and showing us the output file.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/13 02:49:24

Unfortunately sir, nothing changed, so this the information about my system:

Information for general problems.
Code: Select all
== BEGIN uname -rmi ==
2.6.32-220.el6.x86_64 x86_64 x86_64
== END   uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
centos-release-6-2.el6.centos.7.x86_64
== END   rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END   cat /etc/redhat-release ==

== BEGIN getenforce ==
Enforcing
== END   getenforce ==

== BEGIN free -m ==
             total       used       free     shared    buffers     cached
Mem:          3796        620       3176          0         21        261
-/+ buffers/cache:        337       3459
Swap:         5119          0       5119
== END   free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.x86_64
rpm-libs-4.8.0-19.el6.x86_64
rpm-python-4.8.0-19.el6.x86_64
yum-3.2.29-22.el6.centos.noarch
yum-metadata-parser-1.1.2-16.el6.x86_64
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
yum-plugin-security-1.1.30-10.el6.noarch
yum-utils-1.1.30-10.el6.noarch
== END   rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
== END   ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

#  This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
#  It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END   cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit, security
Determining fastest mirrors
Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os error was
14: PYCURL ERROR 6 - "Couldn't resolve host 'mirrorlist.centos.org'"
repo id                       repo name                               status
base                          CentOS-6 - Base                         enabled: 0
c6-media                      CentOS-6 - Media                        disabled
centosplus                    CentOS-6 - Plus                         disabled
contrib                       CentOS-6 - Contrib                      disabled
debug                         CentOS-6 - Debuginfo                    disabled
extras                        CentOS-6 - Extras                       enabled: 0
updates                       CentOS-6 - Updates                      enabled: 0
repolist: 0
== END   yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
== END   egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END   sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==

#
# /etc/fstab
# Created by anaconda on Fri Feb 10 23:23:21 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=e5f122e0-f08b-4bb3-8d60-1f2e247c3e53 /                       ext4    defaults        1 1
UUID=437990ad-a27d-4288-8858-13bd7f5f9141 swap                    swap    defaults        0 0
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
== END   cat /etc/fstab ==

== BEGIN df -h ==
Filesystem            Size  Used Avail Use% Mounted on
/dev/sda3              99G  3.0G   91G   4% /
tmpfs                 1.9G  112K  1.9G   1% /dev/shm
/dev/sr0               54K   54K     0 100% /media/CDROM
== END   df -h ==

== BEGIN fdisk -l ==

Disk /dev/sda: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x7ad03723

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1          13      102400    7  HPFS/NTFS
Partition 1 does not end on cylinder boundary.
/dev/sda2              13        2611    20868096    7  HPFS/NTFS
/dev/sda3            2611       15666   104857600   83  Linux
/dev/sda4           15666       60802   362557440    5  Extended
/dev/sda5           15666       16318     5242880   82  Linux swap / Solaris
/dev/sda6           16319       60802   357311488    7  HPFS/NTFS
== END   fdisk -l ==

== BEGIN blkid ==
/dev/sda1: LABEL="System Reserved" UUID="8C90DDBC90DDAD48" TYPE="ntfs"
/dev/sda2: UUID="DE5EB1795EB14B53" TYPE="ntfs"
/dev/sda3: UUID="e5f122e0-f08b-4bb3-8d60-1f2e247c3e53" TYPE="ext4"
/dev/sda5: UUID="437990ad-a27d-4288-8858-13bd7f5f9141" TYPE="swap"
/dev/sda6: LABEL="New Volume" UUID="126C88FE6C88DE3B" TYPE="ntfs"
== END   blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END   cat /proc/mdstat ==

== BEGIN pvs ==
== END   pvs ==

== BEGIN vgs ==
  No volume groups found
== END   vgs ==

== BEGIN lvs ==
  No volume groups found
== END   lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.el6.x86_64
kernel-firmware-2.6.32-220.el6.noarch
== END   rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e30] (rev 03)
00:02.0 VGA compatible controller [0300]: Intel Corporation 4 Series Chipset Integrated Graphics Controller [8086:2e32] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01)
00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 01)
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA Controller [IDE mode] [8086:27c0] (rev 01)
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v1.0 Gigabit Ethernet [1969:1073] (rev c0)
== END   lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0e8f:0022 GreenAsia Inc.
Bus 004 Device 002: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse
== END   lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
kmod-atl1e-1.0.1.14-1.el6.elrepo.x86_64
== END   rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0      Link encap:Ethernet  HWaddr 1C:6F:65:6D:DF:F1 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:18

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)

== END   ifconfig -a ==

== BEGIN brctl show ==
bridge name   bridge id      STP enabled   interfaces
== END   brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
== END   route -n ==

== BEGIN cat /etc/resolv.conf ==
cat: /etc/resolv.conf: No such file or directory
== END   cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks:   nisplus [NOTFOUND=return] files
#netmasks:   nisplus [NOTFOUND=return] files     
netmasks:   files
networks:   files
netgroup:   nisplus
== END   grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager    0:off   1:off   2:on   3:on   4:on   5:on   6:off
matahari-network   0:off   1:off   2:off   3:off   4:off   5:off   6:off
network           0:off   1:off   2:on   3:on   4:on   5:on   6:off
wpa_supplicant    0:off   1:off   2:off   3:off   4:off   5:off   6:off
== END   chkconfig --list | grep -Ei 'network|wpa' ==



Thanks for replay..
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby pschaff » 2012/02/13 11:44:15

The kmod is installed and you are running 6.2 and not 6.0. The interface is active but does not have an IP address. Check cables and connections to the switch or router. Are there other systems on the same subnet? How are you attempting to manage the network? With the GUI nm-applet? From the command line? With system-config-network?
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: CentOS 6.0 LAN Atheros AR8151 problem

Postby saleh » 2012/02/13 13:21:42

I had checked cables and connections to the switch and router, there is another one system on the subnet, and when i manage my network from "system-config-network", the eth0 interface doesn't be listed.
saleh
 
Posts: 97
Joined: 2011/02/18 18:35:11
Location: ~/egypt/alexandria

Next

Return to CentOS 6 - Hardware Support

Who is online

Users browsing this forum: No registered users and 5 guests