Problem Ralink 3090 Operation not possible due to RF-kill

Issues related to configuring your network

Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/07 20:12:20

Hello, I've been reading this forum in search of a problem that apparently was very similar to what occurs here but I could not find the solution

Problem rtnetlink answers: Operation not possible due to RF-kill

lspci -nn | grep RT
02:00.0 Network controller [0280]: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe [1814:3090]

02:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe
Subsystem: Hewlett-Packard Company Device 1453
Physical Slot: 1
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at d8800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 00-00-90-23-57-82-2a-e0
Kernel driver in use: rt2860
Kernel modules: rt3090sta


ifconfig -a
ra0 Link encap:Ethernet HWaddr E0:2A:82:57:23:90
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17

rpm -qa kmod\* \*firmware
libertas-usb8388-firmware-5.110.22.p23-3.1.el6.noarch
ql2200-firmware-2.02.08-3.1.el6.noarch
rt2860-firmware-26-1.el6.elrepo.noarch
atmel-firmware-1.3-7.el6.noarch
ql23xx-firmware-3.03.27-3.1.el6.noarch
bfa-firmware-3.0.0.0-1.el6.noarch
ql2100-firmware-1.19.38-3.1.el6.noarch
ql2500-firmware-5.06.02-1.el6.noarch
kernel-firmware-2.6.32-220.4.1.el6.centos.plus.noarch
xorg-x11-drv-ati-firmware-6.14.2-7.el6.noarch
aic94xx-firmware-30-2.el6.noarch
ql2400-firmware-5.06.02-1.el6.noarch
zd1211-firmware-1.4-4.el6.noarch
kmod-rt3090sta-2.4.0.4-1.el6.elrepo.x86_64
ivtv-firmware-20080701-20.2.noarch


rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
rfkill unblock all ( remains the same Hard blocked: yes )

helpme plz :S
techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/07 21:10:17

Log messages

Feb 7 17:35:31 TeCHcL kernel: RTMPSetLED::Mode=0,HighByte=0x00,LowByte=0x00
Feb 7 17:35:36 TeCHcL kernel: ERROR!!! H2M_MAILBOX still hold by MCU. command fail
techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Problem Ralink 3090 Operation not possible due to RF-kill

Postby pschaff » 2012/02/09 14:57:16

Please do not hijack threads.

How are you attempting to manage the network connection? CentOS-6 defaults to NetworkManager. No CentOS or 3rd party package I can find provides rtnetlink so I have no idea what that failure means.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/10 11:33:27

Sorry for not read the forum rules. I apologize for my carelessness.

I try to connect me with the icon in the upper pane of the desktop but leaves disabled, and when I try to lift the console, as I show in the log I get the error above and I can not lift my wifi connection.
techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby pschaff » 2012/02/10 12:16:24

Exactly what happens when you attempt to connect using NetworkManager and the nm-applet icon? Are any wireless networks shown? Is the connection encrypted? Can you connect to an unencrypted access point?
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/10 18:37:08

does not show wireless networks (The device is not available), and when I run ifup ra0 I get the following error: rtnetlink answers: Operation not permitted
techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby pschaff » 2012/02/11 17:21:47

Please provide more information about your system by running "./getinfo.sh" and showing us the output file.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/13 11:19:13

Information for general problems.
Code: Select all
== BEGIN uname -rmi ==
2.6.32-220.4.1.el6.centos.plus.x86_64 x86_64 x86_64
== END   uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
epel-release-6-5.noarch
elrepo-release-6-4.el6.elrepo.noarch
adobe-release-x86_64-1.0-1.noarch
rpmforge-release-0.5.2-2.el6.rf.x86_64
remi-release-6-1.el6.remi.noarch
centos-release-6-2.el6.centos.7.x86_64
== END   rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END   cat /etc/redhat-release ==

== BEGIN getenforce ==
Enforcing
== END   getenforce ==

== BEGIN free -m ==
             total       used       free     shared    buffers     cached
Mem:          3734       1189       2545          0         34        569
-/+ buffers/cache:        585       3149
Swap:         7989          0       7989
== END   free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.x86_64
rpm-build-4.8.0-19.el6.x86_64
rpm-libs-4.8.0-19.el6.x86_64
rpm-python-4.8.0-19.el6.x86_64
yum-3.2.29-22.el6.centos.noarch
yum-metadata-parser-1.1.2-16.el6.x86_64
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
yum-plugin-security-1.1.30-10.el6.noarch
yum-utils-1.1.30-10.el6.noarch
== END   rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
adobe-linux-x86_64.repo
CentOS-Base.repo
CentOS-Debuginfo.repo
CentOS-Media.repo
CentOS-Media.repo~
elrepo.repo
epel.repo
epel-testing.repo
google-chrome.repo
google.repo
google.repo~
mirrors-rpmforge
mirrors-rpmforge-extras
mirrors-rpmforge-testing
remi.repo
rpmforge.repo
virtualbox.repo
== END   ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

#  This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
#  It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END   cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, refresh-packagekit, security
Loading mirror speeds from cached hostfile
 * base: mirror.netglobalis.net
 * centosplus: mirror.netglobalis.net
 * elrepo: mirror.symnds.com
 * epel: epel.mirror.mendoza-conicet.gob.ar
 * extras: mirror.netglobalis.net
 * rpmforge: ftp-stud.fht-esslingen.de
 * updates: mirror.netglobalis.net
http://mirror.centos.org/centos/6/contrib/x86_64/repodata/repomd.xml: [Errno 14] PYCURL ERROR 7 - "couldn't connect to host"
Trying other mirror.
repo id                repo name                                  status
adobe-linux-x86_64     Adobe Systems Incorporated                 enabled:     2
base                   CentOS-6 - Base                            enabled: 6,294
c6-media               CentOS-6 - Media                           disabled
centosplus             CentOS-6 - Plus                            enabled:    21
contrib                CentOS-6 - Contrib                         enabled:     0
debug                  CentOS-6 - Debuginfo                       disabled
elrepo                 ELRepo.org Community Enterprise Linux Repo enabled:   162
elrepo-extras          ELRepo.org Community Enterprise Linux Repo disabled
elrepo-kernel          ELRepo.org Community Enterprise Linux Kern disabled
elrepo-testing         ELRepo.org Community Enterprise Linux Test disabled
epel                   Extra Packages for Enterprise Linux 6 - x8 enabled: 6,929
epel-debuginfo         Extra Packages for Enterprise Linux 6 - x8 disabled
epel-source            Extra Packages for Enterprise Linux 6 - x8 disabled
epel-testing           Extra Packages for Enterprise Linux 6 - Te disabled
epel-testing-debuginfo Extra Packages for Enterprise Linux 6 - Te disabled
epel-testing-source    Extra Packages for Enterprise Linux 6 - Te disabled
extras                 CentOS-6 - Extras                          enabled:     4
google-chrome          google-chrome                              enabled:     3
google64               Google - x86_64                            enabled:     4
remi                   Les RPM de remi pour Enterprise Linux 6 -  disabled
remi-test              Les RPM de remi en test pour Enterprise Li disabled
rpmforge               RHEL 6 - RPMforge.net - dag                enabled: 4,202
rpmforge-extras        RHEL 6 - RPMforge.net - extras             disabled
rpmforge-testing       RHEL 6 - RPMforge.net - testing            disabled
updates                CentOS-6 - Updates                         enabled:   338
virtualbox             RHEL/CentOS-6 / x86_64 - VirtualBox        enabled:    17
repolist: 17,976
== END   yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
== END   egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
== END   sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==
#
# /etc/fstab
# Created by anaconda on Tue Jan 24 15:41:15 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=fabd0ff9-a037-4c78-9ad1-4bb764f7c2ca /                       ext4    defaults        1 1
UUID=a18c3556-1db0-4b9e-a877-40b7b9408688 swap                    swap    defaults        0 0
UUID=01863532-2318-442f-b76f-9677e46d1470 swap                    swap    defaults        0 0
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
== END   cat /etc/fstab ==

== BEGIN df -h ==
Filesystem            Size  Used Avail Use% Mounted on
/dev/sda1             155G   23G  125G  16% /
tmpfs                 1.9G  272K  1.9G   1% /dev/shm
== END   df -h ==

== BEGIN fdisk -l ==

Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xa39fe442

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1       20428   164086784   83  Linux
/dev/sda2           20429       38914   148482049    f  W95 Ext'd (LBA)
/dev/sda5           38404       38914     4090880   82  Linux swap / Solaris
/dev/sda6           20429       37894   140291072   83  Linux
/dev/sda7           37894       38403     4090880   82  Linux swap / Solaris

Partition table entries are not in disk order
== END   fdisk -l ==

== BEGIN blkid ==
/dev/sda1: UUID="fabd0ff9-a037-4c78-9ad1-4bb764f7c2ca" TYPE="ext4"
/dev/sda5: UUID="a18c3556-1db0-4b9e-a877-40b7b9408688" TYPE="swap"
/dev/sda6: UUID="89d4afa6-fa68-4775-bf3e-764f757b0b62" TYPE="ext4"
/dev/sda7: UUID="01863532-2318-442f-b76f-9677e46d1470" TYPE="swap"
== END   blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END   cat /proc/mdstat ==

== BEGIN pvs ==
== END   pvs ==

== BEGIN vgs ==
  No volume groups found
== END   vgs ==

== BEGIN lvs ==
  No volume groups found
== END   lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.4.1.el6.centos.plus.x86_64
kernel-2.6.32-220.4.1.el6.x86_64
kernel-2.6.32-220.el6.x86_64
kernel-devel-2.6.32-220.4.1.el6.centos.plus.x86_64
kernel-devel-2.6.32-220.4.1.el6.x86_64
kernel-firmware-2.6.32-220.4.1.el6.centos.plus.noarch
kernel-headers-2.6.32-220.4.1.el6.centos.plus.x86_64
== END   rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03)
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 03)
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] [8086:2929] (rev 03)
02:00.0 Network controller [0280]: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe [1814:3090]
85:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
== END   lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 04f2:b1ac Chicony Electronics Co., Ltd
Bus 008 Device 002: ID 0461:4d22 Primax Electronics, Ltd
== END   lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
== END   rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0      Link encap:Ethernet  HWaddr 64:xx:50:xx:A5:C3 
          inet addr:172.xx.x.75  Bcast:172.xx.x.255  Mask:255.255.255.0
          inet6 addr: fe80::6631:50ff:fe7a:a5c3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6879 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4809 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7910175 (7.5 MiB)  TX bytes:473053 (461.9 KiB)
          Interrupt:32 Base address:0xe000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)

ra0       Link encap:Ethernet  HWaddr E0:2A:82:57:23:90 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:17

== END   ifconfig -a ==

== BEGIN brctl show ==
bridge name   bridge id      STP enabled   interfaces
== END   brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
172.xx.x.0      0.0.0.0         255.255.255.0   U     1      0        0 eth0
0.0.0.0         172.xx.x.1      0.0.0.0         UG    0      0        0 eth0
== END   route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
domain pgnet.cl
search pgnet.cl
nameserver 172.21.50.80
nameserver 172.21.103.10
== END   cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks:   nisplus [NOTFOUND=return] files
#netmasks:   nisplus [NOTFOUND=return] files     
netmasks:   files
networks:   files
netgroup:   nisplus
== END   grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager    0:off   1:off   2:on   3:on   4:on   5:on   6:off
matahari-network   0:off   1:off   2:off   3:off   4:off   5:off   6:off
network           0:off   1:off   2:on   3:on   4:on   5:on   6:off
wpa_supplicant    0:off   1:off   2:off   3:off   4:off   5:off   6:off
== END   chkconfig --list | grep -Ei 'network|wpa' ==



Thx
techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby pschaff » 2012/02/13 11:36:24

Your first post shows kmod-rt3090sta-2.4.0.4-1.el6.elrepo.x86_64 but the script output does not. The ELRepo DeviceIDs does show that it is the correct driver. Try installing it now and rebooting.

It may or may not be relevant to the current problem, but you have multiple 3rd party repos enabled without yum-plugin-priorities. Please read about Installing Software and Repositories, and note the warnings and advice about installing and configuring the yum priorities plugin. Non-core repos should have a higher numeric value, which is a lower priority. Lower is "better" as in golf scores.
pschaff
Retired Moderator
 
Posts: 18277
Joined: 2006/12/13 20:15:34
Location: Tidewater, Virginia, North America

Re: Problem Ralink 3090 Operation not possible due to RF-kill

Postby techcl » 2012/02/13 12:23:10

I did what you told me, reinstall the rt3090 and this is the info:

Information for general problems.
Code: Select all
== BEGIN uname -rmi ==
2.6.32-220.4.1.el6.centos.plus.x86_64 x86_64 x86_64
== END   uname -rmi ==

== BEGIN rpm -qa \*-release\* ==
epel-release-6-5.noarch
elrepo-release-6-4.el6.elrepo.noarch
adobe-release-x86_64-1.0-1.noarch
rpmforge-release-0.5.2-2.el6.rf.x86_64
remi-release-6-1.el6.remi.noarch
centos-release-6-2.el6.centos.7.x86_64
== END   rpm -qa \*-release\* ==

== BEGIN cat /etc/redhat-release ==
CentOS release 6.2 (Final)
== END   cat /etc/redhat-release ==

== BEGIN getenforce ==
Enforcing
== END   getenforce ==

== BEGIN free -m ==
             total       used       free     shared    buffers     cached
Mem:          3734        923       2810          0         33        452
-/+ buffers/cache:        437       3297
Swap:         7989          0       7989
== END   free -m ==

== BEGIN rpm -qa yum\* rpm-\* python | sort ==
python-2.6.6-29.el6.x86_64
rpm-build-4.8.0-19.el6.x86_64
rpm-libs-4.8.0-19.el6.x86_64
rpm-python-4.8.0-19.el6.x86_64
yum-3.2.29-22.el6.centos.noarch
yum-metadata-parser-1.1.2-16.el6.x86_64
yum-plugin-fastestmirror-1.1.30-10.el6.noarch
yum-plugin-priorities-1.1.30-10.el6.noarch
yum-plugin-security-1.1.30-10.el6.noarch
yum-utils-1.1.30-10.el6.noarch
== END   rpm -qa yum\* rpm-\* python | sort ==

== BEGIN ls /etc/yum.repos.d ==
adobe-linux-x86_64.repo
CentOS-Base.repo
CentOS-Base.repo~
CentOS-Debuginfo.repo
CentOS-Media.repo
CentOS-Media.repo~
elrepo.repo
epel.repo
epel-testing.repo
google-chrome.repo
google.repo
google.repo~
mirrors-rpmforge
mirrors-rpmforge-extras
mirrors-rpmforge-testing
remi.repo
rpmforge.repo
virtualbox.repo
== END   ls /etc/yum.repos.d ==

== BEGIN cat /etc/yum.conf ==
[main]
cachedir=/var/cache/yum/$basearch/$releasever
keepcache=0
debuglevel=2
logfile=/var/log/yum.log
exactarch=1
obsoletes=1
gpgcheck=1
plugins=1
installonly_limit=5
bugtracker_url=http://bugs.centos.org/set_project.php?project_id=16&ref=http://bugs.centos.org/bug_report_page.php?category=yum
distroverpkg=centos-release

#  This is the default, if you make this bigger yum won't see if the metadata
# is newer on the remote and so you'll "gain" the bandwidth of not having to
# download the new metadata and "pay" for it by yum not having correct
# information.
#  It is esp. important, to have correct metadata, for distributions like
# Fedora which don't keep old packages around. If you don't like this checking
# interupting your command line usage, it's much better to have something
# manually check the metadata once an hour (yum-updatesd will do this).
# metadata_expire=90m

# PUT YOUR REPOS HERE OR IN separate files named file.repo
# in /etc/yum.repos.d
== END   cat /etc/yum.conf ==

== BEGIN yum repolist all ==
Loaded plugins: fastestmirror, priorities, refresh-packagekit, security
Loading mirror speeds from cached hostfile
 * base: mirror.netglobalis.net
 * centosplus: mirror.netglobalis.net
 * elrepo: mirror.symnds.com
 * epel: epel.mirror.mendoza-conicet.gob.ar
 * extras: mirror.netglobalis.net
 * rpmforge: ftp-stud.fht-esslingen.de
 * updates: mirror.netglobalis.net
94 packages excluded due to repository priority protections
repo id                repo name                               status
adobe-linux-x86_64     Adobe Systems Incorporated              enabled:        2
base                   CentOS-6 - Base                         enabled:    6,294
c6-media               CentOS-6 - Media                        disabled
centosplus             CentOS-6 - Plus                         enabled:     15+6
contrib                CentOS-6 - Contrib                      enabled:        0
debug                  CentOS-6 - Debuginfo                    disabled
elrepo                 ELRepo.org Community Enterprise Linux R enabled:    159+3
elrepo-extras          ELRepo.org Community Enterprise Linux R disabled
elrepo-kernel          ELRepo.org Community Enterprise Linux K disabled
elrepo-testing         ELRepo.org Community Enterprise Linux T disabled
epel                   Extra Packages for Enterprise Linux 6 - enabled: 6,843+86
epel-debuginfo         Extra Packages for Enterprise Linux 6 - disabled
epel-source            Extra Packages for Enterprise Linux 6 - disabled
epel-testing           Extra Packages for Enterprise Linux 6 - disabled
epel-testing-debuginfo Extra Packages for Enterprise Linux 6 - disabled
epel-testing-source    Extra Packages for Enterprise Linux 6 - disabled
extras                 CentOS-6 - Extras                       enabled:        4
google-chrome          google-chrome                           enabled:        3
google64               Google - x86_64                         enabled:        4
remi                   Les RPM de remi pour Enterprise Linux 6 disabled
remi-test              Les RPM de remi en test pour Enterprise disabled
rpmforge               RHEL 6 - RPMforge.net - dag             enabled:  4,197+5
rpmforge-extras        RHEL 6 - RPMforge.net - extras          disabled
rpmforge-testing       RHEL 6 - RPMforge.net - testing         disabled
updates                CentOS-6 - Updates                      enabled:      338
virtualbox             RHEL/CentOS-6 / x86_64 - VirtualBox     enabled:       17
repolist: 17,876
== END   yum repolist all ==

== BEGIN egrep 'include|exclude' /etc/yum.repos.d/*.repo ==
/etc/yum.repos.d/CentOS-Base.repo:includepkgs=kernel* jfsutils reiserfs-utils
/etc/yum.repos.d/CentOS-Base.repo:exclude=postfix-*plus*
== END   egrep 'include|exclude' /etc/yum.repos.d/*.repo ==

== BEGIN sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==
priority = 1 [base]
priority = 1 [centosplus]
priority = 1 [extras]
priority = 1 [updates]
priority = 2 [contrib]
== END   sed -n -e "/^\[/h; /priority *=/{ G; s/\n/ /; s/ity=/ity = /; p }" /etc/yum.repos.d/*.repo | sort -k3n ==

== BEGIN cat /etc/fstab ==
#
# /etc/fstab
# Created by anaconda on Tue Jan 24 15:41:15 2012
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=fabd0ff9-a037-4c78-9ad1-4bb764f7c2ca /                       ext4    defaults        1 1
UUID=a18c3556-1db0-4b9e-a877-40b7b9408688 swap                    swap    defaults        0 0
UUID=01863532-2318-442f-b76f-9677e46d1470 swap                    swap    defaults        0 0
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
== END   cat /etc/fstab ==

== BEGIN df -h ==
Filesystem            Size  Used Avail Use% Mounted on
/dev/sda1             155G   22G  125G  15% /
tmpfs                 1.9G  112K  1.9G   1% /dev/shm
== END   df -h ==

== BEGIN fdisk -l ==

Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xa39fe442

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1       20428   164086784   83  Linux
/dev/sda2           20429       38914   148482049    f  W95 Ext'd (LBA)
/dev/sda5           38404       38914     4090880   82  Linux swap / Solaris
/dev/sda6           20429       37894   140291072   83  Linux
/dev/sda7           37894       38403     4090880   82  Linux swap / Solaris

Partition table entries are not in disk order
== END   fdisk -l ==

== BEGIN blkid ==
/dev/sda1: UUID="fabd0ff9-a037-4c78-9ad1-4bb764f7c2ca" TYPE="ext4"
/dev/sda5: UUID="a18c3556-1db0-4b9e-a877-40b7b9408688" TYPE="swap"
/dev/sda6: UUID="89d4afa6-fa68-4775-bf3e-764f757b0b62" TYPE="ext4"
/dev/sda7: UUID="01863532-2318-442f-b76f-9677e46d1470" TYPE="swap"
== END   blkid ==

== BEGIN cat /proc/mdstat ==
Personalities :
unused devices: <none>
== END   cat /proc/mdstat ==

== BEGIN pvs ==
== END   pvs ==

== BEGIN vgs ==
  No volume groups found
== END   vgs ==

== BEGIN lvs ==
  No volume groups found
== END   lvs ==

== BEGIN rpm -qa kernel\* | sort ==
kernel-2.6.32-220.4.1.el6.centos.plus.x86_64
kernel-2.6.32-220.4.1.el6.x86_64
kernel-2.6.32-220.el6.x86_64
kernel-devel-2.6.32-220.4.1.el6.centos.plus.x86_64
kernel-devel-2.6.32-220.4.1.el6.x86_64
kernel-firmware-2.6.32-220.4.1.el6.centos.plus.noarch
kernel-headers-2.6.32-220.4.1.el6.centos.plus.x86_64
== END   rpm -qa kernel\* | sort ==

== BEGIN lspci -nn ==
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03)
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 03)
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] [8086:2929] (rev 03)
02:00.0 Network controller [0280]: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe [1814:3090]
85:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
== END   lspci -nn ==

== BEGIN lsusb ==
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 04f2:b1ac Chicony Electronics Co., Ltd
Bus 008 Device 002: ID 0461:4d22 Primax Electronics, Ltd
== END   lsusb ==

== BEGIN rpm -qa kmod\* kmdl\* ==
kmod-rt3090sta-2.4.0.4-1.el6.elrepo.x86_64
== END   rpm -qa kmod\* kmdl\* ==

== BEGIN ifconfig -a ==
eth0      Link encap:Ethernet  HWaddr 64:xx:x0:7A:A5:C3 
          inet addr:172.21.6.75  Bcast:172.xx.x.255  Mask:255.255.255.0
          inet6 addr: fe80::6631:50ff:fe7a:a5c3/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:654 errors:0 dropped:0 overruns:0 frame:0
          TX packets:410 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:240082 (234.4 KiB)  TX bytes:43134 (42.1 KiB)
          Interrupt:32 Base address:0xa000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)

ra0       Link encap:Ethernet  HWaddr E0:2A:82:57:23:90 
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:17

== END   ifconfig -a ==

== BEGIN brctl show ==
bridge name   bridge id      STP enabled   interfaces
== END   brctl show ==

== BEGIN route -n ==
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
172.xx.x.0      0.0.0.0         255.255.255.0   U     1      0        0 eth0
0.0.0.0         172.xx.x.1      0.0.0.0         UG    0      0        0 eth0
== END   route -n ==

== BEGIN cat /etc/resolv.conf ==
# Generated by NetworkManager
domain pgnet.cl
search pgnet.cl
nameserver 172.XX.XX.80
nameserver 172.XX.XXX.10
== END   cat /etc/resolv.conf ==

== BEGIN grep net /etc/nsswitch.conf ==
#networks:   nisplus [NOTFOUND=return] files
#netmasks:   nisplus [NOTFOUND=return] files     
netmasks:   files
networks:   files
netgroup:   nisplus
== END   grep net /etc/nsswitch.conf ==

== BEGIN chkconfig --list | grep -Ei 'network|wpa' ==
NetworkManager    0:off   1:off   2:on   3:on   4:on   5:on   6:off
matahari-network   0:off   1:off   2:off   3:off   4:off   5:off   6:off
network           0:off   1:off   2:on   3:on   4:on   5:on   6:off
wpa_supplicant    0:off   1:off   2:off   3:off   4:off   5:off   6:off
== END   chkconfig --list | grep -Ei 'network|wpa' ==

techcl
 
Posts: 8
Joined: 2012/02/07 18:27:53

Next

Return to CentOS 6 - Networking Support

Who is online

Users browsing this forum: No registered users and 3 guests